Phone: 0049 (0)30 315 700 0
- You are here:
- Paints & Tools
- Helpers
- Fillers
The epoxy putty with a thousand uses in modelling D.I.Y and industry.
For plastic model not suitable, if necessary, use Product: Plastic Putty 359/BD44.
Drying time 2-3 hours, overnight it becomes bone-hard, 113 grams per pack.
Processing instructions
Take two equal parts of each stick and knead them for at least 5 minutes until you get a uniform mass without stripes. Then knead some more.
The surface on which the filler is applied must be absolutely free of grease and clean.
Smooth surfaces should be cleaned with appropriate solvent or soap and warm
water to remove any dirt residue. Sanding the substrate allows for better adhesion of the filler. This can now be applied and will cure without shrinking in three to four hours.
Milliput reacts to water at all stages of application, from initial mixing to application.
To make corrections and avoid unwanted unevenness, they should moisten their hands and tools. If necessary, work with Milliput can also be carried out under a fine water jet. To achieve the desired surface, apply the putty and smooth it immediately with a damp finger or press on the desired texture, e.g. with a damp cloth.
If you use tools to work with Milliput, clean them immediately after use with a damp cloth. If Milliput hardens on a tool, it is almost impossible to remove it.
Like other chemicals, Milliput can cause skin irritation. Therefore, wear rubber or disposable gloves when mixing the compound. Rubber gloves are best washed under running water immediately after use, as if you were washing your hands. If you are working without gloves, wash your hands with soap and water immediately after use.
Storage
Milliput should be stored in a cool place. Although we give a shelf life of about two years for Milliput, we know from some customers that they use it for much longer. (In fact, we have heard from one customer that he has managed to refresh Milliput after ten years by heating it in the microwave. A
method we do not recommend, however.)
We recommend keeping Milliput in a cool, dry place and resealing the protective cover tightly after use.
Additional information for white Milliput Superfine:
As practically both components are the same colour, it is very important to knead the mixture well for at
five minutes at least, although no visible change takes place.
If you are using Milliput for the first time....
If you have not worked with Milliput before, we recommend that you first familiarise yourself with the material and its texture before tackling a repair. Take about a quarter of both components and knead them for at least five minutes. Then form a small ball and press it flat, about the size of a coin.
Now watch how Milliput behaves over the next two to three hours. At the beginning, right after mixing, the mass is tough and sticky. After about an hour, Milliput becomes rubbery and less sticky. After about three to four hours, the mass becomes completely hard and no longer sticks. Overnight, Milliput hardens as hard as a rock.
For plastic model not suitable, if necessary, use Product: Plastic Putty 359/BD44.
Drying time 2-3 hours, overnight it becomes bone-hard, 113 grams per pack.
Processing instructions
Take two equal parts of each stick and knead them for at least 5 minutes until you get a uniform mass without stripes. Then knead some more.
The surface on which the filler is applied must be absolutely free of grease and clean.
Smooth surfaces should be cleaned with appropriate solvent or soap and warm
water to remove any dirt residue. Sanding the substrate allows for better adhesion of the filler. This can now be applied and will cure without shrinking in three to four hours.
Milliput reacts to water at all stages of application, from initial mixing to application.
To make corrections and avoid unwanted unevenness, they should moisten their hands and tools. If necessary, work with Milliput can also be carried out under a fine water jet. To achieve the desired surface, apply the putty and smooth it immediately with a damp finger or press on the desired texture, e.g. with a damp cloth.
If you use tools to work with Milliput, clean them immediately after use with a damp cloth. If Milliput hardens on a tool, it is almost impossible to remove it.
Like other chemicals, Milliput can cause skin irritation. Therefore, wear rubber or disposable gloves when mixing the compound. Rubber gloves are best washed under running water immediately after use, as if you were washing your hands. If you are working without gloves, wash your hands with soap and water immediately after use.
Storage
Milliput should be stored in a cool place. Although we give a shelf life of about two years for Milliput, we know from some customers that they use it for much longer. (In fact, we have heard from one customer that he has managed to refresh Milliput after ten years by heating it in the microwave. A
method we do not recommend, however.)
We recommend keeping Milliput in a cool, dry place and resealing the protective cover tightly after use.
Additional information for white Milliput Superfine:
As practically both components are the same colour, it is very important to knead the mixture well for at
five minutes at least, although no visible change takes place.
If you are using Milliput for the first time....
If you have not worked with Milliput before, we recommend that you first familiarise yourself with the material and its texture before tackling a repair. Take about a quarter of both components and knead them for at least five minutes. Then form a small ball and press it flat, about the size of a coin.
Now watch how Milliput behaves over the next two to three hours. At the beginning, right after mixing, the mass is tough and sticky. After about an hour, Milliput becomes rubbery and less sticky. After about three to four hours, the mass becomes completely hard and no longer sticks. Overnight, Milliput hardens as hard as a rock.
- Group
- Filler

Warning, irritant!

Warning, harmful to environment!
Not a toy! Not suitable for children under the age of 14!
Documents
The Milliput Company LTD
Dolgellau Gwynedd
LL40 1UU Mid Wales
Vereinigtes Königreich
E-Mail: [email protected]
Website: www.milliput.com
Responsible person
Berliner Zinnfiguren
Knesebeckstr. 88
10623 Berlin
Deutschland
[email protected]
Dolgellau Gwynedd
LL40 1UU Mid Wales
Vereinigtes Königreich
E-Mail: [email protected]
Website: www.milliput.com
Responsible person
Berliner Zinnfiguren
Knesebeckstr. 88
10623 Berlin
Deutschland
[email protected]
We also recommend this article
The following articles may also interest you
Take a look at our similar products.Copyright © 2026 Berliner Zinnfiguren & Preussisches Buecherkabinett
Berliner Zinnfiguren, Knesebeckstr. 88, 10623 Berlin, Germany
Phone 0049 (30) 315 700 0