Berliner Zinnfiguren/Paints & Tools/Helpers/Glues/Tools for adhesives products

Roket Blaster 11,60 €

Sat, 18 Apr 2026 07:10:23 +0200

Activator spray for cyanoacrylate adhesives (accelerator for instant adhesives). For bonding sensitive surfaces.
Spray or brush onto one surface at a time. Apply the cyanoacrylate adhesive (not enclosed) to the other component and join. The adhesive will then set immediately. CFC-free.

Cyanoacrylate Glue Activator 9,75 €

Tue, 12 May 2026 06:45:09 +0200

Activator is specially formulated to accelerate the curing time of cyanoacrylate glue.

Activator is specially formulated to accelerate the drying of cyanoacrylate glue. It has two systems of application: it can be used with the diffuser quickly and comfortably or with the brush inside for greater precision. This allows an almost immediate and highly durable union of even the smallest parts. It can be applied using two different methods:

Before applying cyanoacrylate: moisten the joint surface with the product and allow it to evaporate for 10-15 seconds. Then apply the glue and quickly join the two pieces together. The parts will bond almost immediately. After applying cyanoacrylate: once the pieces have been joined, apply Activator over the cyanoacrylate. The joint will cure completely in 2-3 seconds, creating a very strong bond.

Be careful to seal the container tightly. Use the accelerator with the appropriate protective equipment including gloves, clothing, and eye protection while working in a well-ventilated area. Store away from heat. Keep out of reach of children. Avoid contact with the skin and eyes.

DEBONDER (20mL) 9,75 €

Sun, 07 Jun 2026 07:55:06 +0200

This liquid solvent allows modellers to eliminate those annoying traces of cyanoacrylate adhesive that remain on the surface after building.

Debonder can be used on a wide range of surfaces including plastic, resin, and photo etch. Simply apply using a brush or a pipette onto the glue and let it act for about 45 seconds. Then clean the surface with a cloth. If necessary, these steps can be repeated until the cyanoacrylate is completely removed. Do not use this product over painted surfaces.

Always keep this container out of reach of children and tightly sealed, use the solvent with protective equipment in an adequately ventilated area safe from high temperatures. Keep out of reach of children and avoid contact with skin and eyes. If contact occurs, thoroughly rinse immediately with water.

ERASER - CLEANER FOR CYANOCRYLATE GLUE EXCESS REMOVER 6,25 €

Mon, 01 Jun 2026 06:50:14 +0200

20g.
* Softens and removes already hardened cyanoacrylate adhesives.
* Ideal for small touches once the piece has been glued.

HOW TO USE:
* Treat the surface to be cleaned by rubbing with paper towels dipped in
ERASER cleaner.
* Clean the surfaces, while they are damp, with paper towels, in order to
eliminate the remains of the ERASER cleaner.
* Bottles are not filled at a 100% to leave some air and make it work properly.

FLASH - ACCELERATOR FOR CYANOACRYLATE GLUE 10,50 €

Mon, 01 Jun 2026 06:50:14 +0200

CA-glue activator designed to reduce the bonding time to mere seconds.
Especially useful for gluing elements with small contact surface.

C/A Applicator 8,95 €

Tue, 21 Apr 2026 07:50:11 +0200

Intelligent design for clean work.

Hold the applicator in one hand and dip the tip into a drop of superglue. The applicator now picks up a minimal amount of glue and allows cleanest application at the point of use.

Easy to clean with acetone or a blade.

Microbrush - Blue / Regular Brush 6,55 €

Mon, 01 Jun 2026 06:50:14 +0200

For precise and accurate application of glue, paints, decal solutions etc.
Flexible, tapered heads for easy positioning - excellent for those hard to reach places and compound curves.
Items Green Yellow and White - application fibres are made from a non-absorbent, non-linting material which creates and holds a nondrip bubble of media ready for application.
Item Black - is a brush made from non-absorbent, non-linting bristles that will hold a bubble of solution as small as 3 mm - allows for precise and efficient solution application.

Pack contains 25 brushes.

UHU Patafix white 6,25 €

Fri, 01 May 2026 07:25:12 +0200

80 removable and reusable adhesive pads. For fixing and fastening e.g. when gluing or painting. Best mounting aid.

Suitable for removable and at the same time permanent bonding of smaller objects to wood, cement, glass, metal, plastic and porcelain. Suitable for attaching posters, decorations, small electronic devices, cables and much more.

Surface requirements:
The surfaces to be stuck must be dry and free of dust and grease.

Instructions for use:
1) Peel off the pads and 2) Knead until soft. 3) Apply UHU patafix to the object to be fixed. 4) Fix the object to the desired surface by pressing firmly. To reuse: repeat the steps from 2).

Properties:
- Removable and reusable
- Quick and clean attachment
- Permanent adhesion
- Dermatologically tested
- Made in Germany

Personal safety:
Keep out of reach of children: There is a risk of mistaking the adhesive pads for chewing gum.

Stains/residue:
Possible residue can be removed by dabbing with another adhesive pad. UHU patafix may possibly leave a greasy mark on absorbent surfaces; these can normally be removed with benzine.
Storage conditions

The product should be stored in a dry, cool and frost-free place.

Micro Tips & Tube 7,80 €

Sun, 07 Jun 2026 07:15:05 +0200

For precise application of cyanoacrylate adhesives.

Roket Re-Cap 5,95 €

Tue, 28 Apr 2026 07:40:05 +0200

Replacement cap and nozzles to get your Roket instant glue flowing like new again.

Glue Buster 8,95 €

Sat, 06 Jun 2026 07:10:16 +0200

Debonder and dissolver of superglue.
Releases bonded skin and removes supergue stain. Stays on site faster debonding action.

Roket Powder 40g 8,80 €

Thu, 28 May 2026 06:40:05 +0200

A powder for use with super glue.

It fills gaps and strengthens glue points. Flows in gaps like gel and can be precisely dosed and shaped. Cures in seconds with "Roket Hot" (359 / AD43) or "Roket Rapid" (359 / AD44). Can be filed and drilled.

40g bottle

Tamiya CA Cement Micro Nozzles 2.5 mm 3,45 €

Sun, 07 Jun 2026 08:05:04 +0200

-Micro Nozzles x10
- These micro nozzles are for use with Tamiya CA Cement.
- Very fine nozzles allow the cement to reach the tip via capillary action, where it hardens to block off the cement until the next use.
- Pipe diameter (section connecting with Tamiya CA Cement) : 2.5mm (Item 53580 is 3.0mm.)
- Compatible with Item 87062 and 54511.

One-Drop Applicator with 2 Tubes 8,50 €

Wed, 10 Jun 2026 06:40:09 +0200

One-Drop applicator vials allow precise control of liquid adhesives and other low viscosity substances.

15 ml bottle with 0.5 mm and 0.4 mm interchangeable steel needles and protective cap.

Tamiya CA Accelerator 10ml bottle 11,25 €

Sat, 18 Apr 2026 08:40:15 +0200

- This CA Cement Accelerator enables quicker curing of CA cement. Apply the accelerator to one
cementing surface and the CA cement to the other. A strong bond will quickly form when the two
surfaces are pressed together. This is ideal for attaching small photo-etched parts or parts with a
very small cementing surface.
- The bottle's cap has an applicator brush to ensure easy application.
- This is an alcohol-based accelerator that keeps damage to plastic parts to a minimum.
- One bottle contains 10ml.

Touch-N-Flow Applicator 8,95 €

Sat, 18 Apr 2026 08:20:06 +0200

Revolutionise your bonding technique!

The exact right amount of adhesive, in exactly the right place!

With the Plast-i-Weld plastic adhesive:
Clean bonding by exploiting the capillary effect. The very fluid adhesive penetrates into the smallest cracks and crevices as if by itself. Due to its short reaction time and high efficiency, it fuses plastic parts without leaving any large residues. Work in long strokes without having to interrupt the bonding process.

The safe method when working with painted parts. Excess evaporates enormously quickly, helping to prevent damage.

Pin Flow Applicator 13,95 €

Mon, 01 Jun 2026 06:30:11 +0200

A specially-designed applicator devised for scale modellers, model railway enthusiasts & dollshouse miniaturists, the Deluxe Materials Pin Flow Applicator (AC11) will also be useful to many other hobbyists.

Pin Point Bottle Kit 7,80 €

Sat, 18 Apr 2026 07:10:23 +0200

Plastic bottle with 3 fine tips for precise bonding with water-based adhesives. Excellent for fixing ballast. Can be washed off with water.

Tamiya Ca Rubber Tire Cement LoVis. 25g 13,10 €

Sat, 18 Apr 2026 08:40:15 +0200

- Special cyanoacrylate adhesive (superglue) for RC car tires
- Very thin viscosity for perfect tire mounting
- 25g contents, including nozzle and aluminum pouch
1 Tamiya CA tire adhesive, super thin,
25g, with dispensing nozzle,
Suitable for all rubber tires.

WARNING!!!
H315 Causes skin irritation
H319 Causes serious eye irritation
H335 May cause respiratory irritation
EUH202 Cyanoacrylate. Danger!
Bonds skin and eyelids together in seconds. Keep out of reach of children.

Caution! Not suitable for children under 14 years.

Touch-N-Flow Filler Bottle 8,95 €

Sat, 18 Apr 2026 08:20:06 +0200

Perfect for filling the Touch-N-Flow applicator bottle.