Berliner Zinnfiguren/Paints & Tools/Paints/AMMO/AMMO Single paints products

TRANSPARATOR 17 ML 2,50 €

Mon, 01 Jun 2026 06:50:14 +0200

Water based thinner specifically designed for use with Ammo acrylics, also compatible with other acrylic brands as well. This is the necessary product for painting semi-transparent acrylic coats with brush or airbrush easily without changing the quality and finish of paint. It is water soluble, odorless, and non-toxic. Shake well before each use. It includes a stainless steel agitator to facilitate mixture. Dries completely in 24 hours. Jar of 17 mL.

ArmorFX Zimmerit Paste 4,50 €

Tue, 09 Jun 2026 06:50:07 +0200

The Zimmerit coating, developed by the German chemical company Chemische Werke Zimmer & Co., was applied to German armored vehicles in mid-late WWII, specifically from August 1943 until September 1944. This coating had the function of protecting armored vehicles from infantry HEAT magnetic mines being placed on their surfaces. The idea was to apply a coat of Zimmerit paste on the armor to create a rough, non-magnetic surface that reduced the chances of mines sticking to the vehicle.
The coating was imprinted with textured patterns, often wavy or grid-shaped, using special tools. These patterns were not only highly distinctive, but also increased the effectiveness of the Zimmerit by reducing the contact area of the magnets with the surface of the vehicle.
AMMO presents the first quick-drying acrylic paste to represent Zimmerit coatings on your models. Apply the Zimmerit paste to the model using a spatula, then use one of the Zimmerit tools included in the set A.MIG-8583 Zimmerit Applicator to reproduce the authentic patterns easily and realistically. This paste has the same color as the original paste, providing an extremely authentic finish to your models.

ULTRA-MATT LUCKY VARNISH 2,95 €

Sun, 14 Jun 2026 07:50:05 +0200

Flat medium/varnish for all kinds of acrylic paints. Guarantees 100% flat finishes. This varnish can be used in two different ways:
- used straight from the jar as a regular varnish after painting to achieve a dead flat finish.
- it can also be used as a flat medium by adding it to acrylic paints.

Varnish application has long been one of the biggest challenges for modelers. Many have ruined a few models due to the use of poor quality or inappropriate varnishes for the job at hand, and the thing is that the varnishing process is an extremely important step of the build. For the first time, AMMO releases a complete varnish range for winning results on each and every model.
These acrylic varnishes will allow you to get the best results with both brush and airbrush in a very simple manner. It must be used in thin layers, and can be applied directly from the jar without thinning for a perfect finish. When used through the airbrush, we recommend spraying 6 inches (15 cm) away from the surface. It is non-toxic and odorless, and dries completely in 24 hours.
This new varnish range was carefully developed over a lengthy period to ensure the modeler a perfect result every time. Don´t take your chances, use LUCKY VARNISH, a winning product that will rule out any mishap that may occur when using ordinary varnishes. Available in all the usual finishes used in scale modeling, from high gloss to dead flat.

Easy to use and simple to clean. Incredible transparent finishes for all of your models, and accurate for all subjects. Will not yellow or alter colors.
Perfect for both brush and airbrush.
1- Using an airbrush, apply in light and short passes using 1.2 bar (17psi) air pressure, avoiding build up.
2- Let dry at least 5 minutes between coats. Do NOT flood the surface.
3- Let it dry completely for 12 hours.
No thinning needed. Clean with or water

MATT LUCKY VARNISH (17 ml) 2,95 €

Wed, 20 May 2026 06:45:15 +0200

Varnish application has long been one of the biggest challenges for modelers. Many have ruined a few models due to the use of poor quality or inappropriate varnishes for the job at hand, and the thing is that the varnishing process is an extremely important step of the build. For the first time, AMMO releases a complete varnish range for winning results on each and every model.

These acrylic varnishes will allow you to get the best results with both brush and airbrush in a very simple manner. It must be used in thin layers, and can be applied directly from the jar without thinning for a perfect finish. When used through the airbrush, we recommend spraying 6 inches (15 cm) away from the surface. It is non-toxic and odorless, and dries completely in 24 hours.

This new varnish range was carefully developed over a lengthy period to ensure the modeler a perfect result every time. Don´t take your chances, use LUCKY VARNISH, a winning product that will rule out any mishap that may occur when using ordinary varnishes. Available in all the usual finishes used in scale modeling, from high gloss to dead flat.

SATIN LUCKY VARNISH (17 mL) 2,95 €

Tue, 28 Apr 2026 08:00:08 +0200

GLOSSY LUCKY VARNISH (17 mL) 2,95 €

Fri, 22 May 2026 06:45:09 +0200

FS 26373 SILVER GREY 2,45 €